pfsync



PFSYNC(4)                    Device Drivers Manual                   PFSYNC(4)


NAME

     pfsync - packet filter state table synchronisation interface


SYNOPSIS

     pseudo-device pfsync


DESCRIPTION

     The pfsync interface is a pseudo-device which exposes certain changes to
     the state table used by pf(4).  State changes can be viewed by invoking
     tcpdump(8) on the pfsync interface.  If configured with a physical
     synchronisation interface, pfsync will also send state changes out on
     that interface, and insert state changes received on that interface from
     other systems into the state table.

     By default, all local changes to the state table are exposed via pfsync.
     State changes from packets received by pfsync over the network are not
     rebroadcast.  Updates to states created by a rule marked with the no-sync
     keyword are ignored by the pfsync interface (see pf.conf(5) for details).

     The pfsync interface will attempt to collapse multiple state updates into
     a single packet where possible.  The maximum number of times a single
     state can be updated before a pfsync packet will be sent out is
     controlled by the maxupd parameter to ifconfig (see ifconfig(8) and the
     example below for more details).  The sending out of a pfsync packet will
     be delayed by a maximum of one second.

     Where more than one firewall might actively handle packets, e.g. with
     certain ospfd(8), bgpd(8) or carp(4) configurations, it is beneficial to
     defer transmission of the initial packet of a connection.  The pfsync
     state insert message is sent immediately; the packet is queued until
     either this message is acknowledged by another system, or a timeout has
     expired.  This behaviour is enabled with the defer parameter to
     ifconfig(8).


NETWORK SYNCHRONISATION

     States can be synchronised between two or more firewalls using this
     interface, by specifying a synchronisation interface using ifconfig(8).
     For example, the following command configures an address on fxp0 and sets
     it as the synchronisation interface:

           # ifconfig fxp0 inet 172.19.13.1/28
           # ifconfig pfsync0 syncdev fxp0

     By default, state change messages are sent out on the synchronisation
     interface using IP multicast packets to the 224.0.0.240 group address.
     An alternative destination address for pfsync packets can be specified
     using the syncpeer keyword.

     It is important that the pfsync traffic be well secured as there is no
     authentication on the protocol and it would be trivial to spoof packets
     which create states, bypassing the pf ruleset.  Only run the pfsync
     protocol on a trusted network - ideally a network dedicated to pfsync
     messages such as a crossover cable between two firewalls.


EXAMPLES

     pfsync and carp(4) can be used together to provide automatic failover of
     a pair of firewalls configured in parallel.  One firewall will handle all
     traffic until it dies, is shut down, or is manually demoted, at which
     point the second firewall will take over automatically.

     Both firewalls in this example have three sis(4) interfaces.  sis0 is the
     external interface, on the 10.0.0.0/24 subnet; sis1 is the internal
     interface, on the 192.168.0.0/24 subnet; and sis2 is the pfsync
     interface, using the 192.168.254.0/24 subnet.  A crossover cable connects
     the two firewalls via their sis2 interfaces.  On all three interfaces,
     firewall A uses the .254 address, while firewall B uses .253.  The
     interfaces are configured as follows (firewall A unless otherwise
     indicated):

     /etc/hostname.sis0:

           inet 10.0.0.254 255.255.255.0 NONE

     /etc/hostname.sis1:

           inet 192.168.0.254 255.255.255.0 NONE

     /etc/hostname.sis2:

           inet 192.168.254.254 255.255.255.0 NONE

     /etc/hostname.carp0:

           inet 10.0.0.1 255.255.255.0 10.0.0.255 vhid 1 pass foo

     /etc/hostname.carp1:

           inet 192.168.0.1 255.255.255.0 192.168.0.255 vhid 2 pass bar

     /etc/hostname.pfsync0:

           up syncdev sis2

     pf(4) must also be configured to allow pfsync and carp(4) traffic
     through.  The following should be added to the top of /etc/pf.conf:

           pass quick on { sis2 } proto pfsync keep state (no-sync)
           pass on { sis0 sis1 } proto carp keep state (no-sync)

     It is preferable that one firewall handle the forwarding of all the
     traffic, therefore the advskew on the backup firewall's carp(4)
     interfaces should be set to something higher than the primary's.  For
     example, if firewall B is the backup, its /etc/hostname.carp1 would look
     like this:

           inet 192.168.0.1 255.255.255.0 192.168.0.255 vhid 2 pass bar \
                   advskew 100

     The following must also be added to /etc/sysctl.conf:

           net.inet.carp.preempt=1


SEE ALSO

     bpf(4), carp(4), inet(4), inet6(4), netintro(4), pf(4), hostname.if(5),
     pf.conf(5), protocols(5), ifconfig(8), ifstated(8), tcpdump(8)


HISTORY

     The pfsync device first appeared in OpenBSD 3.3.

     The pfsync protocol and kernel implementation were significantly modified
     between OpenBSD 4.4 and OpenBSD 4.5.  The two protocols are incompatible
     and will not interoperate.


BUGS

     pfsync does not currently work with ipsec(4).

OpenBSD 5.9                      June 25, 2015                     OpenBSD 5.9

[Unix Hosting | Open-Source | Contact Us]
[Engineering & Automation | Software Development | Server Applications]